Struct rp2040_pac::I2C1

pub struct I2C1 { /* private fields */ }

DW_apb_i2c address block

List of configuration constants for the Synopsys I2C hardware (you may see references to these in I2C register header; these are fixed values, set at hardware design time):

IC_ULTRA_FAST_MODE ……………. 0x0
IC_UFM_TBUF_CNT_DEFAULT ……….. 0x8
IC_UFM_SCL_LOW_COUNT ………….. 0x0008
IC_UFM_SCL_HIGH_COUNT …………. 0x0006
IC_TX_TL …………………….. 0x0
IC_TX_CMD_BLOCK ………………. 0x1
IC_HAS_DMA …………………… 0x1
IC_HAS_ASYNC_FIFO …………….. 0x0
IC_SMBUS_ARP …………………. 0x0
IC_FIRST_DATA_BYTE_STATUS ……… 0x1
IC_INTR_IO …………………… 0x1
IC_MASTER_MODE ……………….. 0x1
IC_DEFAULT_ACK_GENERAL_CALL ……. 0x1
IC_INTR_POL ………………….. 0x1
IC_OPTIONAL_SAR ………………. 0x0
IC_DEFAULT_TAR_SLAVE_ADDR ……… 0x055
IC_DEFAULT_SLAVE_ADDR …………. 0x055
IC_DEFAULT_HS_SPKLEN ………….. 0x1
IC_FS_SCL_HIGH_COUNT ………….. 0x0006
IC_HS_SCL_LOW_COUNT …………… 0x0008
IC_DEVICE_ID_VALUE ……………. 0x0
IC_10BITADDR_MASTER …………… 0x0
IC_CLK_FREQ_OPTIMIZATION ………. 0x0
IC_DEFAULT_FS_SPKLEN ………….. 0x7
IC_ADD_ENCODED_PARAMS …………. 0x0
IC_DEFAULT_SDA_HOLD …………… 0x000001
IC_DEFAULT_SDA_SETUP ………….. 0x64
IC_AVOID_RX_FIFO_FLUSH_ON_TX_ABRT . 0x0
IC_CLOCK_PERIOD ………………. 100
IC_EMPTYFIFO_HOLD_MASTER_EN ……. 1
IC_RESTART_EN ………………… 0x1
IC_TX_CMD_BLOCK_DEFAULT ……….. 0x0
IC_BUS_CLEAR_FEATURE ………….. 0x0
IC_CAP_LOADING ……………….. 100
IC_FS_SCL_LOW_COUNT …………… 0x000d
APB_DATA_WIDTH ……………….. 32
IC_SDA_STUCK_TIMEOUT_DEFAULT …… 0xffffffff
IC_SLV_DATA_NACK_ONLY …………. 0x1
IC_10BITADDR_SLAVE ……………. 0x0
IC_CLK_TYPE ………………….. 0x0
IC_SMBUS_UDID_MSB …………….. 0x0
IC_SMBUS_SUSPEND_ALERT ………… 0x0
IC_HS_SCL_HIGH_COUNT ………….. 0x0006
IC_SLV_RESTART_DET_EN …………. 0x1
IC_SMBUS …………………….. 0x0
IC_OPTIONAL_SAR_DEFAULT ……….. 0x0
IC_PERSISTANT_SLV_ADDR_DEFAULT …. 0x0
IC_USE_COUNTS ………………… 0x0
IC_RX_BUFFER_DEPTH ……………. 16
IC_SCL_STUCK_TIMEOUT_DEFAULT …… 0xffffffff
IC_RX_FULL_HLD_BUS_EN …………. 0x1
IC_SLAVE_DISABLE ……………… 0x1
IC_RX_TL …………………….. 0x0
IC_DEVICE_ID …………………. 0x0
IC_HC_COUNT_VALUES ……………. 0x0
I2C_DYNAMIC_TAR_UPDATE ………… 0
IC_SMBUS_CLK_LOW_MEXT_DEFAULT ….. 0xffffffff
IC_SMBUS_CLK_LOW_SEXT_DEFAULT ….. 0xffffffff
IC_HS_MASTER_CODE …………….. 0x1
IC_SMBUS_RST_IDLE_CNT_DEFAULT ….. 0xffff
IC_SMBUS_UDID_LSB_DEFAULT ……… 0xffffffff
IC_SS_SCL_HIGH_COUNT ………….. 0x0028
IC_SS_SCL_LOW_COUNT …………… 0x002f
IC_MAX_SPEED_MODE …………….. 0x2
IC_STAT_FOR_CLK_STRETCH ……….. 0x0
IC_STOP_DET_IF_MASTER_ACTIVE …… 0x0
IC_DEFAULT_UFM_SPKLEN …………. 0x1
IC_TX_BUFFER_DEPTH ……………. 16

Implementations

impl I2C1

pub const PTR: *const RegisterBlock = {0x40048000 as *const i2c0::RegisterBlock}

Pointer to the register block

pub const fn ptr() -> *const RegisterBlock

Return the pointer to the register block

pub unsafe fn steal() -> Self

Steal an instance of this peripheral

Safety

Ensure that the new instance of the peripheral cannot be used in a way that may race with any existing instances, for example by only accessing read-only or write-only registers, or by consuming the original peripheral and using critical sections to coordinate access between multiple new instances.

Additionally, other software such as HALs may rely on only one peripheral instance existing to ensure memory safety; ensure no stolen instances are passed to such software.

Methods from Deref<Target = RegisterBlock>

pub fn ic_con(&self) -> &IC_CON

0x00 - I2C Control Register. This register can be written only when the DW_apb_i2c is disabled, which corresponds to the IC_ENABLE[0] register being set to 0. Writes at other times have no effect.

Read/Write Access: - bit 10 is read only. - bit 11 is read only - bit 16 is read only - bit 17 is read only - bits 18 and 19 are read only.

pub fn ic_tar(&self) -> &IC_TAR

0x04 - I2C Target Address Register

This register is 12 bits wide, and bits 31:12 are reserved. This register can be written to only when IC_ENABLE[0] is set to 0.

Note: If the software or application is aware that the DW_apb_i2c is not using the TAR address for the pending commands in the Tx FIFO, then it is possible to update the TAR address even while the Tx FIFO has entries (IC_STATUS[2]= 0). - It is not necessary to perform any write to this register if DW_apb_i2c is enabled as an I2C slave only.

pub fn ic_sar(&self) -> &IC_SAR

0x08 - I2C Slave Address Register

pub fn ic_data_cmd(&self) -> &IC_DATA_CMD

0x10 - I2C Rx/Tx Data Buffer and Command Register; this is the register the CPU writes to when filling the TX FIFO and the CPU reads from when retrieving bytes from RX FIFO.

The size of the register changes as follows:

Write: - 11 bits when IC_EMPTYFIFO_HOLD_MASTER_EN=1 - 9 bits when IC_EMPTYFIFO_HOLD_MASTER_EN=0 Read: - 12 bits when IC_FIRST_DATA_BYTE_STATUS = 1 - 8 bits when IC_FIRST_DATA_BYTE_STATUS = 0 Note: In order for the DW_apb_i2c to continue acknowledging reads, a read command should be written for every byte that is to be received; otherwise the DW_apb_i2c will stop acknowledging.

pub fn ic_ss_scl_hcnt(&self) -> &IC_SS_SCL_HCNT

0x14 - Standard Speed I2C Clock SCL High Count Register

pub fn ic_ss_scl_lcnt(&self) -> &IC_SS_SCL_LCNT

0x18 - Standard Speed I2C Clock SCL Low Count Register

pub fn ic_fs_scl_hcnt(&self) -> &IC_FS_SCL_HCNT

0x1c - Fast Mode or Fast Mode Plus I2C Clock SCL High Count Register

pub fn ic_fs_scl_lcnt(&self) -> &IC_FS_SCL_LCNT

0x20 - Fast Mode or Fast Mode Plus I2C Clock SCL Low Count Register

pub fn ic_intr_stat(&self) -> &IC_INTR_STAT

0x2c - I2C Interrupt Status Register

Each bit in this register has a corresponding mask bit in the IC_INTR_MASK register. These bits are cleared by reading the matching interrupt clear register. The unmasked raw versions of these bits are available in the IC_RAW_INTR_STAT register.

pub fn ic_intr_mask(&self) -> &IC_INTR_MASK

0x30 - I2C Interrupt Mask Register.

These bits mask their corresponding interrupt status bits. This register is active low; a value of 0 masks the interrupt, whereas a value of 1 unmasks the interrupt.

pub fn ic_raw_intr_stat(&self) -> &IC_RAW_INTR_STAT

0x34 - I2C Raw Interrupt Status Register

Unlike the IC_INTR_STAT register, these bits are not masked so they always show the true status of the DW_apb_i2c.

pub fn ic_rx_tl(&self) -> &IC_RX_TL

0x38 - I2C Receive FIFO Threshold Register

pub fn ic_tx_tl(&self) -> &IC_TX_TL

0x3c - I2C Transmit FIFO Threshold Register

pub fn ic_clr_intr(&self) -> &IC_CLR_INTR

0x40 - Clear Combined and Individual Interrupt Register

pub fn ic_clr_rx_under(&self) -> &IC_CLR_RX_UNDER

0x44 - Clear RX_UNDER Interrupt Register

pub fn ic_clr_rx_over(&self) -> &IC_CLR_RX_OVER

0x48 - Clear RX_OVER Interrupt Register

pub fn ic_clr_tx_over(&self) -> &IC_CLR_TX_OVER

0x4c - Clear TX_OVER Interrupt Register

pub fn ic_clr_rd_req(&self) -> &IC_CLR_RD_REQ

0x50 - Clear RD_REQ Interrupt Register

pub fn ic_clr_tx_abrt(&self) -> &IC_CLR_TX_ABRT

0x54 - Clear TX_ABRT Interrupt Register

pub fn ic_clr_rx_done(&self) -> &IC_CLR_RX_DONE

0x58 - Clear RX_DONE Interrupt Register

pub fn ic_clr_activity(&self) -> &IC_CLR_ACTIVITY

0x5c - Clear ACTIVITY Interrupt Register

pub fn ic_clr_stop_det(&self) -> &IC_CLR_STOP_DET

0x60 - Clear STOP_DET Interrupt Register

pub fn ic_clr_start_det(&self) -> &IC_CLR_START_DET

0x64 - Clear START_DET Interrupt Register

pub fn ic_clr_gen_call(&self) -> &IC_CLR_GEN_CALL

0x68 - Clear GEN_CALL Interrupt Register

pub fn ic_enable(&self) -> &IC_ENABLE

0x6c - I2C Enable Register

pub fn ic_status(&self) -> &IC_STATUS

0x70 - I2C Status Register

This is a read-only register used to indicate the current transfer status and FIFO status. The status register may be read at any time. None of the bits in this register request an interrupt.

When the I2C is disabled by writing 0 in bit 0 of the IC_ENABLE register: - Bits 1 and 2 are set to 1 - Bits 3 and 10 are set to 0 When the master or slave state machines goes to idle and ic_en=0: - Bits 5 and 6 are set to 0

pub fn ic_txflr(&self) -> &IC_TXFLR

0x74 - I2C Transmit FIFO Level Register This register contains the number of valid data entries in the transmit FIFO buffer. It is cleared whenever: - The I2C is disabled - There is a transmit abort - that is, TX_ABRT bit is set in the IC_RAW_INTR_STAT register - The slave bulk transmit mode is aborted The register increments whenever data is placed into the transmit FIFO and decrements when data is taken from the transmit FIFO.

pub fn ic_rxflr(&self) -> &IC_RXFLR

0x78 - I2C Receive FIFO Level Register This register contains the number of valid data entries in the receive FIFO buffer. It is cleared whenever: - The I2C is disabled - Whenever there is a transmit abort caused by any of the events tracked in IC_TX_ABRT_SOURCE The register increments whenever data is placed into the receive FIFO and decrements when data is taken from the receive FIFO.

pub fn ic_sda_hold(&self) -> &IC_SDA_HOLD

0x7c - I2C SDA Hold Time Length Register

The bits [15:0] of this register are used to control the hold time of SDA during transmit in both slave and master mode (after SCL goes from HIGH to LOW).

The bits [23:16] of this register are used to extend the SDA transition (if any) whenever SCL is HIGH in the receiver in either master or slave mode.

Writes to this register succeed only when IC_ENABLE[0]=0.

The values in this register are in units of ic_clk period. The value programmed in IC_SDA_TX_HOLD must be greater than the minimum hold time in each mode (one cycle in master mode, seven cycles in slave mode) for the value to be implemented.

The programmed SDA hold time during transmit (IC_SDA_TX_HOLD) cannot exceed at any time the duration of the low part of scl. Therefore the programmed value cannot be larger than N_SCL_LOW-2, where N_SCL_LOW is the duration of the low part of the scl period measured in ic_clk cycles.

pub fn ic_tx_abrt_source(&self) -> &IC_TX_ABRT_SOURCE

0x80 - I2C Transmit Abort Source Register

This register has 32 bits that indicate the source of the TX_ABRT bit. Except for Bit 9, this register is cleared whenever the IC_CLR_TX_ABRT register or the IC_CLR_INTR register is read. To clear Bit 9, the source of the ABRT_SBYTE_NORSTRT must be fixed first; RESTART must be enabled (IC_CON[5]=1), the SPECIAL bit must be cleared (IC_TAR[11]), or the GC_OR_START bit must be cleared (IC_TAR[10]).

Once the source of the ABRT_SBYTE_NORSTRT is fixed, then this bit can be cleared in the same manner as other bits in this register. If the source of the ABRT_SBYTE_NORSTRT is not fixed before attempting to clear this bit, Bit 9 clears for one cycle and is then re-asserted.

pub fn ic_slv_data_nack_only(&self) -> &IC_SLV_DATA_NACK_ONLY

0x84 - Generate Slave Data NACK Register

The register is used to generate a NACK for the data part of a transfer when DW_apb_i2c is acting as a slave-receiver. This register only exists when the IC_SLV_DATA_NACK_ONLY parameter is set to 1. When this parameter disabled, this register does not exist and writing to the register’s address has no effect.

A write can occur on this register if both of the following conditions are met: - DW_apb_i2c is disabled (IC_ENABLE[0] = 0) - Slave part is inactive (IC_STATUS[6] = 0) Note: The IC_STATUS[6] is a register read-back location for the internal slv_activity signal; the user should poll this before writing the ic_slv_data_nack_only bit.

pub fn ic_dma_cr(&self) -> &IC_DMA_CR

0x88 - DMA Control Register

The register is used to enable the DMA Controller interface operation. There is a separate bit for transmit and receive. This can be programmed regardless of the state of IC_ENABLE.

pub fn ic_dma_tdlr(&self) -> &IC_DMA_TDLR

0x8c - DMA Transmit Data Level Register

pub fn ic_dma_rdlr(&self) -> &IC_DMA_RDLR

0x90 - I2C Receive Data Level Register

pub fn ic_sda_setup(&self) -> &IC_SDA_SETUP

0x94 - I2C SDA Setup Register

This register controls the amount of time delay (in terms of number of ic_clk clock periods) introduced in the rising edge of SCL - relative to SDA changing - when DW_apb_i2c services a read request in a slave-transmitter operation. The relevant I2C requirement is tSU:DAT (note 4) as detailed in the I2C Bus Specification. This register must be programmed with a value equal to or greater than 2.

Writes to this register succeed only when IC_ENABLE[0] = 0.

Note: The length of setup time is calculated using [(IC_SDA_SETUP - 1) * (ic_clk_period)], so if the user requires 10 ic_clk periods of setup time, they should program a value of 11. The IC_SDA_SETUP register is only used by the DW_apb_i2c when operating as a slave transmitter.

pub fn ic_ack_general_call(&self) -> &IC_ACK_GENERAL_CALL

0x98 - I2C ACK General Call Register

The register controls whether DW_apb_i2c responds with a ACK or NACK when it receives an I2C General Call address.

This register is applicable only when the DW_apb_i2c is in slave mode.

pub fn ic_enable_status(&self) -> &IC_ENABLE_STATUS

0x9c - I2C Enable Status Register

The register is used to report the DW_apb_i2c hardware status when the IC_ENABLE[0] register is set from 1 to 0; that is, when DW_apb_i2c is disabled.

If IC_ENABLE[0] has been set to 1, bits 2:1 are forced to 0, and bit 0 is forced to 1.

If IC_ENABLE[0] has been set to 0, bits 2:1 is only be valid as soon as bit 0 is read as ‘0’.

Note: When IC_ENABLE[0] has been set to 0, a delay occurs for bit 0 to be read as 0 because disabling the DW_apb_i2c depends on I2C bus activities.

pub fn ic_fs_spklen(&self) -> &IC_FS_SPKLEN

0xa0 - I2C SS, FS or FM+ spike suppression limit

This register is used to store the duration, measured in ic_clk cycles, of the longest spike that is filtered out by the spike suppression logic when the component is operating in SS, FS or FM+ modes. The relevant I2C requirement is tSP (table 4) as detailed in the I2C Bus Specification. This register must be programmed with a minimum value of 1.

pub fn ic_clr_restart_det(&self) -> &IC_CLR_RESTART_DET

0xa8 - Clear RESTART_DET Interrupt Register

pub fn ic_comp_param_1(&self) -> &IC_COMP_PARAM_1

0xf4 - Component Parameter Register 1

Note This register is not implemented and therefore reads as 0. If it was implemented it would be a constant read-only register that contains encoded information about the component’s parameter settings. Fields shown below are the settings for those parameters

pub fn ic_comp_version(&self) -> &IC_COMP_VERSION

0xf8 - I2C Component Version Register

pub fn ic_comp_type(&self) -> &IC_COMP_TYPE

0xfc - I2C Component Type Register

Trait Implementations

impl Debug for I2C1

fn fmt(&self, f: &mut Formatter<'_>) -> Result

Formats the value using the given formatter.

impl Deref for I2C1

type Target = RegisterBlock

The resulting type after dereferencing.

fn deref(&self) -> &Self::Target

Dereferences the value.

impl Send for I2C1