Type Alias IC_SDA_HOLD

pub type IC_SDA_HOLD = Reg<IC_SDA_HOLD_SPEC>;

IC_SDA_HOLD (rw) register accessor: I2C SDA Hold Time Length Register

The bits [15:0] of this register are used to control the hold time of SDA during transmit in both slave and master mode (after SCL goes from HIGH to LOW).

The bits [23:16] of this register are used to extend the SDA transition (if any) whenever SCL is HIGH in the receiver in either master or slave mode.

Writes to this register succeed only when IC_ENABLE[0]=0.

The values in this register are in units of ic_clk period. The value programmed in IC_SDA_TX_HOLD must be greater than the minimum hold time in each mode (one cycle in master mode, seven cycles in slave mode) for the value to be implemented.

The programmed SDA hold time during transmit (IC_SDA_TX_HOLD) cannot exceed at any time the duration of the low part of scl. Therefore the programmed value cannot be larger than N_SCL_LOW-2, where N_SCL_LOW is the duration of the low part of the scl period measured in ic_clk cycles.

You can read this register and get ic_sda_hold::R. You can reset, write, write_with_zero this register using ic_sda_hold::W. You can also modify this register. See API.

For information about available fields see ic_sda_hold module

Aliased Type

struct IC_SDA_HOLD { /* private fields */ }

Implementations

impl<REG: Resettable + Writable> Reg<REG>

pub fn reset(&self)

Writes the reset value to Writable register.

Resets the register to its initial state.

pub fn write<F>(&self, f: F)

where F: FnOnce(&mut W<REG>) -> &mut W<REG>,

Writes bits to a Writable register.

You can write raw bits into a register:

periph.reg.write(|w| unsafe { w.bits(rawbits) });

or write only the fields you need:

periph.reg.write(|w| w
    .field1().bits(newfield1bits)
    .field2().set_bit()
    .field3().variant(VARIANT)
);

or an alternative way of saying the same:

periph.reg.write(|w| {
    w.field1().bits(newfield1bits);
    w.field2().set_bit();
    w.field3().variant(VARIANT)
});

In the latter case, other fields will be set to their reset value.

impl<REG: Writable> Reg<REG>

pub unsafe fn write_with_zero<F>(&self, f: F)

where F: FnOnce(&mut W<REG>) -> &mut W<REG>,

Writes 0 to a Writable register.

Similar to write, but unused bits will contain 0.

Safety

Unsafe to use with registers which don’t allow to write 0.

impl<REG: Readable + Writable> Reg<REG>

pub fn modify<F>(&self, f: F)

where for<'w> F: FnOnce(&R<REG>, &'w mut W<REG>) -> &'w mut W<REG>,

Modifies the contents of the register by reading and then writing it.

E.g. to do a read-modify-write sequence to change parts of a register:

periph.reg.modify(|r, w| unsafe { w.bits(
   r.bits() | 3
) });

or

periph.reg.modify(|_, w| w
    .field1().bits(newfield1bits)
    .field2().set_bit()
    .field3().variant(VARIANT)
);

or an alternative way of saying the same:

periph.reg.modify(|_, w| {
    w.field1().bits(newfield1bits);
    w.field2().set_bit();
    w.field3().variant(VARIANT)
});

Other fields will have the value they had before the call to modify.

impl<REG: RegisterSpec> Reg<REG>

pub fn as_ptr(&self) -> *mut REG::Ux

Returns the underlying memory address of register.

let reg_ptr = periph.reg.as_ptr();

impl<REG: Readable> Reg<REG>

pub fn read(&self) -> R<REG>

Reads the contents of a Readable register.

You can read the raw contents of a register by using bits:

let bits = periph.reg.read().bits();

or get the content of a particular field of a register:

let reader = periph.reg.read();
let bits = reader.field1().bits();
let flag = reader.field2().bit_is_set();

Trait Implementations

impl<REG: RegisterSpec> Send for Reg<REG>

where REG::Ux: Send,